Help Center Type your question Or Choose a category
to find the help you need

Error message for RC models 2018 and older

 

Display (level 1) Display (level 2)
by pressing the left arrow
Description Probable Cause/Event Corrective Actions
E 1 0031 Stuck in Place - Robomow got stuck in place. It cannot continue driving.
- Drive wheel motors have been working under a severe load.
- Robomow has difficulty turning in place because the front wheel is blocked by a ditch or non-level ground.
- Remove the mower away from this particular location and restart operation.
- Rectify the reason for it getting stuck.
- Check the ground around the mower for ditches or non-level ground. Fill with dirt and level off.
- Check if the drive wheels are free to rotate and nothing is blocking them.
- Verify that the cutting height is not set too low for the grass condition - increase the cutting height if needed
0027 Start Elsewhere Drive wheel motors have been working under severe load during automatic or manual operation - Check to insure the mower is not stuck, causing the drive wheels to slip.
- Check the ground around the mower for holes or indentations. Fill with dirt and level off.
- Check if the drive wheels are free to rotate and nothing is blocking them.
- Remove the mower away from this particular location and restart operation
E 2 0028 Cross Outside - the Perimeter Wire is too close to the edge.
- the lawn slope is too big.
- Robomow does not succeed to turn in place at the edge and it causes the Mower to slip out of the designated area.
- Robomow has slipped out of the Perimeter Wire lope because of sloping area or wet grass.
- Remove the wire towards the inner part of the lawn.
- Do not include this area because of its steep slopes.
- Fill holes and pits in the ground.
- Increase the cutting height.
0030 Start Inside Automatic operation is initiated while the robot is placed out of the Perimeter Wire loop. Place the mower inside the lawn and renew the operation
E 3 0012 No wire signal - Power Box/Perimeter Switch is not turned on or not connected
- Power Box may need to be restarted
- The Perimeter Wire is not connected to the Base Station/Perimeter Switch.
- The Perimeter Wire is cut.
- Make sure the Base Station is connected to the mains supply.
- Disconnect the Power Box from the mains power and reconnect after 10 seconds.
- Check that the low voltage cable between the Power Box and the Base Station is connected.
- Check the LED indications on the Power Box.
- Check the connection of the Perimeter Wire to the Base Station / Perimeter Switch.
- Check the installation for cut wire. Repair broken cable with the waterproofed connector supplied in the box.
E 4 0023 Check Power - Power Box is not plugged in properly into the Power outlet.
- No Power at the Power outlet or the main Power is shut off.
- the Mower or Base Station contacts are dirty.
- Charging is not detected, although there is a physical contact between the Mower and the Base Station contacts.
- Confirm Power Box is plugged into the power outlet.
- Turn power on to the power outlet.
- Check the power outlet using another appliance.
- Clean the contacts with a brush or piece of cloth.
- Confirm a good connection of the Power Box to the Base Station.
E 5 0010 Mow overheat The mowing motor has been working under a severe load for too long. No need for action – Robomow will renew automatically the operation after the mowing motor will cool down.
0021 Check mowing height Mowing motor has faced over-current conditions for too long as a result of high grass or an obstacle that is stuck or wrapped around the blade.
- Something is preventing a blade from rotating freely. Severe grass accumulation under the mowing deck, rope, or similar object is wrapped around mowing blade.
CAUTION – Switch Off the Safety Switch before checking the blade.
- Inspect the blade for foreign material or debris preventing rotation.
- Clean out accumulated grass clippings using a wooden stick.
0022 Check mowing motor Mowing motor has faced over-current for too long in the Base Station before starting the operation CAUTION – Switch Off the Safety Switch before checking the blade.
- Remove the mower from the Base Station. Inspect the blade for foreign material or debris preventing rotation.
E 6 0011 Drive overheat The drive motors have been working under a severe load for too long No need to do anything.
Robomow will renew the operation automatically as soon as the drive motor will cool down.
E 7 0014 Front wheel problem The Front Wheel has left the ground for too long during operation. - If Robomow has driven onto an obstacle, Switch off the Safety Switch, raising the front end: Remove or exclude the object from the mowing area.
- If Robomow is being used on a slope too steep for safe mowing, exclude this from the mowing area.
- If high grass is preventing the front wheel from fully turning on the ground, raise the cutting height.
- If the ground contains large holes or indentations where the front wheel can drop into when passing across, fill these areas with dirt and level off.
E 8 0061 Decrease Inactive Time - Too many Inactive Days and/or Hours have been set for your lawn area. Current settings will not be changed.
- Mowing Frequency is too high for current settings of Inactive Time. The Inactive Time settings will be set to defaults.
- Area setting is too high for current settings of Inactive Time. The Inactive Time settings will be set to defaults.
- Decrease the number of Inactive Days and/or the number of Inactive Hours to allow Robomow to complete mowing your lawn.
- Decrease Mowing Frequency (p001)
- Decrease Area setting
E 9 0015 Key pressed One of the operating panel buttons is constantly pressed. Press 'OK' to confirm the message and continue operation. This message is displayed to inform only.
0016 Low temperature - Mower does not depart automatically from the Base Station when the ambiance temperature is lower than 5ºC (41ºF).
- Information - When the temperature is below 5ºC (41ºF) the grass does not grow or grows very slowly. However Manual Depart is enabled.
- No need to do anything.
- Robomow will renew the operation automatically as soon as the ambiance temperature will rise above 5ºC (41ºF).
0020 Rain detected - The operation is delayed as Robomow detects rain.
- Robomow should resume operation 30 minutes after it stops to detect the rain.
- No need for action.
- The message is displayed until Robomow will not detect rain and then will start mowing.
0026 Base problem Robomow fails to enter the Base Station several consecutive times - Adjust the Base Station position.
- Clean the contacts with a brush or piece of cloth.
0060 Intensity error The mowing hours % value you have set is too high for your lawn area. Decrease the mowing hours % you have set for the zone(s) in your lawn.

 

 

 

 

 

 

RC_error_codes_table.jpg